Showing results: 1276 - 1290 of 2617 items found.
-
KDL Series -
Bemco Inc.
The Bemco KDL series is designed for production testing of electronic circuit boards and completed electronic systems. They accept Bemco KDLC Carts that have a working area of 42 wide by 60 high by 48 deep suspended on insulated runners and casters 11 inches above the test area floor.
-
PeakTech Prüf- und Messtechnik GmbH
This AC / DC laboratory power supply has two separately adjustable outputs which can dispense AC/DC voltages from 0 - 30 V as well as DC/AC current 0 - 6 A. Due to the possibilities offered by this device, it is also suitable for the maintenance of small AC circuits, transformers and lights.
-
S-Probe -
PacketMicro Inc.
S-Probe series of single-ended probes can perform up to 20 GHz are designed for RF, power integrity, and signal integrity testing. Its strong beryllium copper (BeCu) tips is perfect for direct probing of uneven surfaces, such as solder pads and circuit components. This is a big improvement over the fragile microprobes.
-
UWE Electronics
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
#9003A -
Innovative Products of America
portable trailer tester for testing lights and electric brakes on light-duty type trailers (7 spade, 6 round, 5 and 4 pin). The Mini MUTT places a load on the trailer's electrical circuits to verify proper lighting function. The Mini MUTT is powered by an (optional) internal 12v battery,
-
BS407 -
Aim-TTi
High basic accuracy of 0.1%Wide range of 1 µΩ to 20 kΩCurrent reversal switch for detecting thermal EMF effectsCurrent diversion switch for easy zeroingFour terminal measurement using Kelvin clip leads (supplied)Battery operation with built-in charger20mV clamp for "dry circuit" testing
-
ChenYang Technologies GmbH & Co. KG
is a sophisticated Hall Effect Gear Tooth IC featuring an on-chip 12-bit A/DConverter and logic that acts as a digital sample and hold circuit. A separate 6-bit D/A converterprovides a fixed hysteresis. The sensor does not have a chopper delay. It uses a single Hall platewhich is immune to rotary alignment problems.
-
Analog Devices Inc.
Analog Devices offers a range of supervisory circuits that offer a complete single chip solution for power supply monitoring and battery control functions in microprocessor systems. Functions include microprocessor reset, backup battery switchover, watchdog timers, CMOS RAM write protection, and power failure warning.
-
Renesas Electronics Corp.
High-speed CMOS output photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a CMOS output IC on the output side. This coupler is a high common mode transient immunity (CMR), high-speed CMOS output type device designed for high-speed logic interface circuits.
-
EE105T-xx -
Executive Engineering
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
QT 4256 ATE -
Qmax Test Technologies Pvt. Ltd.
QT 4256 ATE is a combination Board Functional Test System , a main frame Automated Test Equipment (ATE) which can be configured up to maximum of 1280 Bi-directional digital channels ideal for testing circuit card assemblies of high level of complexity and whether it is a legacy or new generation PCB.
-
ZD1500 -
Teledyne LeCroy
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
ZD500 -
Teledyne LeCroy
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
ZD1000 -
Teledyne LeCroy
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
Silent Solutions LLC
As wireless continues to be a significant growth opportunity, SILENT works with commercial and industrial manufacturers to ensure time-to-market for RF and wireless enabled products. We design, build, and test RF and wireless solutions - within budget and cost guidelines - for consumer grade products and high performance circuits and systems.